We Are PayPal Verified  

 

Specialist on bose delco, Speaker Amplifier,Louisiana Delco Radio Repair Center,We have the CD Radios unlock Codes,Display Bulbs for GM Radios,We Have the Delco Unlock Code,Gm Delco Radio Knobs

 Click on the PayPal Icon, to Pay and send the 4 or 6 Display Numbers For the Delco Radio Unlock Code!

Home PageAbout UsContact UsSite MapCD RadiosCassetteSpeakersBose AmpsShippingQ & AMailing ListWires ColorsLinksCommentsElectronicsPartsAfterMarketC4 C5 Part CDRepairCost$OldRadioKnobsTheft Loc II buttons

 Etronics 88x31 banner 

 

Visitors:
 

Click on the paypal Icon, Put the 4 or 6 Display Numbers in the Payment for Line:

Do this first

 

1. Press and hold presets 2 & 3 or 1&4 for about 10  seconds until the  first  2 or 3 digits of the display code are displayed.


2. Write the numbers down.


3. Press the AM/FM button; write down the next 2 or 3 numbers.

 

Click on the Paypal Icon Above, and put the 4 or 6 Display on the Payment for information:

When you get the Unlock Code from Us, do this next:

Go back to the car, Do this: 

1 Press the HR  button and set the first 2 or 3 numbers.

2 Press Minute  button and set the next 2 or 3 last numbers.

3 Press AM/FM  button, SEC "-----"should be displayed.

4  You can  now turn the radio on.

Click Here  to E-Mail the The Six Numbers

Corvetteradios@CorvetteRadios.Com

Pay $26 with Paypal, or E-mail us with your Visa,MasterCard Numbers

If your Radio say "InOP"

This means too many wrong codes have been entered and the radio must be left power up for 1 hour with battery and ignition applied before 3 more attempts can be made.

Thank you.

"If you have a "RDS" Radio, we can't unlock that one"

corvetteradios

_______________________Thank you_____________________

If you have a "RDS"Radio, like this one >Img183.png<We can not Unlock "RDS" Radios

Note 1: Different model radios have different button to set the codes into the radio.To determine which two to use, detetmine if the radio has a Seek Button, a seek Up/Down button, or no seek button at all. If the radio has a seek button, use seeek and scan to set the codes as decribed below If the radio has a seek Up/Down button, use seek Up/Down and tune Up/Down to set the codes and substitute these buttons for seek and scan in the procedures below.

      Note 2: Different model radios have different functions attached to the radio presets. Below is the present known configuration of dual functions depending on having a seek button, seek Up/Down or no seek button at all.

      What the Buttons on some radios are

  • SEEK BUTTON-Presets 1(PREV), 2(NEXT), 3(REV), 4(FF), 5(COMP)

    SEEK UP/DOWN-Presets 1(PREV), 2(NEXT), 3(REV), 4(FF), 5(COMP)

    NO SEEK-Presets 1(REV), 2(FF), 3(COMP), 4(REPT), 5(SRCH), 6(SCAN)

--------------------------------------------------------------------------------------------------------------------------------------------------------------

    To Add a Customer Code> Set User Code (Activate) from Unlock mode

  1. With the radio ON, hold in presets 1 and 4 for about 4 seconds until the display changes to"----"
  2. Press the set Button
  3. Set the first digit (0-9) of your code with the seek button.
  4. Set the next two digits (0-99) of your code with the scan button.
  5. Press the am-fm button to enter the first three digits.
  6. Again, use the seek to set the 4th digit (0-9) of your code.
  7. set the last two digit (0-9) of your code with the scan button.
  8. Press the AM-FM button to enter the last 3 digits of your code.
  9. When 'REP' then'000' are displayed, repeat steps 3 through 8 of this procedure to enter your code again before the display changes back to clock. This confirms your customer code, activates the theft deterrent, and after step 8, displays the'SEC' to show the theft deterrent has been activated. Any time battery power is cycled and the ignition is applied the display will show "LOC" and needs to be Unlocked by either your customer code or the factory backup code. please write down the codes.

 

 

 

 

 

 

 

Note: If "SEC" is Displayed, the theft deterrent is already activated.This means the the old code must be removed first before entering a new code.

gmdelogo1.png

Setting the key Remote control for your> Silverado,Tahce, GMC

1. SIT IN VEHICLE AND CLOSE DOOR

2. HOLD FINGER DOWN ON UNLOCK POWER DOOR LOCK SWITCH ON DRIVERS DOOR.

3. TURN IGNITION ON / OFF, ON / OFF.LEAVE KEY IN IGNITION, (DO NOT START VEHICLE, ON POSITION IS THE POSITION BEFORE START)

4. RELEASE FINGER FROM POWER DOOR LOCK.POWER DOOR LOCKS WILL CYCLE, (JUMP UP AND DOWN)

5. PRESS AND HOLD BOTH THE LOCK AND UNLOCK BUTTONS ON NEW REMOTE UNTILL YOU HEAR POWER DOOR LOCKS CYCLE, (JUMP UP AND DOWN) YOU MAY HAVE TO HOLD BOTH BUTTONS DOWN FOR 5- 20 SECONDS.

6. TAKE 2ND NEW, OR OLD REMOTE AND HOLD BOTH UNLOCK AND LOCK BUTTONS DOWN UNTILL LOCKS CYCLE.(MAY TAKE 5- 20 SECONDS)


7. TURN KEY ON, THEN OFF.YOU ARE DONE,  
    EXIT VEHICLE AND TRY YOUR REMOTE.

  

 

 

    

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

  

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Home Page | About Us | Contact Us | Site Map | Used Delco CD Radios | Used Delco Cassette Radios | Used Delco Speakers | Used Bose Amplifiers 

 Shipping to Us | TroublesShooting | Join The Mailing list | GM Plugs & Colors | Link's | Customer Comments | New & Used Parts

 Copyright 1999-2004 CorvetteRadios.com All Rights Reserved